The solution to the rear door lock.
The solution to the rear door lock is not closed mainly includes the following aspects:
Check the door handle: If you use the door handle to lock the door, check whether the door handle is loose. If they are loose, you may need to replace them with new doorknobs.
Check the mechanical lock: If you use a mechanical key to lock the door, you need to check whether the mechanical lock is loose or damaged. If it is loose or damaged, a new mechanical lock needs to be replaced.
Check the remote control battery: If you use the remote control to lock the door, you need to check whether the remote control battery is out of power or damaged. If it is out of power or damaged, a new battery needs to be replaced.
Check the smart key: The smart key uses low-intensity radio waves, and may not work properly if there is strong magnetic field signal interference around the car. In this case, you can try to move the smart key closer to the vehicle or change the location.
Check trunk lock block control wiring: If the rear door is connected to the trunk, you may need to check the trunk lock block control wiring for problems, such as disconnected or damaged wiring. If it is a line problem, it needs to be inspected and re-tightened.
Check the trunk hydraulic support rod: Failure of the trunk hydraulic support rod may also cause the rear door to fail to lock. If the support rod fails, a new support rod may need to be replaced.
Check the trunk door lock machine: The mechanical control failure of the rear door lock machine can also cause the rear door to fail to lock. In this case, it may be necessary to replace the rear door lock machine.
To sum up, the solution to the problem of the rear door lock does not need to be inspected and repaired according to the specific situation, which may involve the inspection and replacement of the door handle, mechanical lock, remote control battery, smart key, trunk lock block control line, trunk hydraulic support rod or tail door lock machine.
The rear door lock won't snap back, the door won't close
The rear door lock does not spring back and the door does not close can be caused by several reasons:
If the buckle position is incorrect, adjust the position relationship between the buckle and the buckle. You can use a tool such as a screwdriver to gently adjust the buckle, and then close the door to adjust until it fits.
Rust on the lock hook: This can cause the door latch to not spring back. The solution can be to apply rust remover or butter evenly to the hook and latch.
Insufficient lubricating oil inside the door lock: Fill the right amount of lubricating oil inside the door lock can be solved.
The inside of the door lock is too greasy: it is necessary to clean the inside of the door lock, it is recommended to go to the 4S shop to be handled by professionals.
Winter car wash door lock frozen: Make sure to dry the door lock after washing the car to avoid freezing.
Damaged or worn latches: New latches may be needed.
Loose or damaged door handle or latch: Check and re-tighten or replace.
When solving these problems, care should be taken not to close the door too forcefully to avoid further damage. Pay attention to safety during inspection and repair to avoid injury. When replacing parts, use original or brand parts to ensure quality and reliability. If you can not solve the problem, you should seek the help of professional maintenance personnel in time. Test after repair to ensure the door can be closed and locked properly.
The back door of the car won't close. What happened
There may be a variety of reasons why the rear doors of a car cannot be closed, but here are a few possible scenarios:
Door lock machine failure: The door lock machine is a key component that controls the door switch, and if it fails, it may cause the door to fail to close.
Door stuck or blocked: There may be debris, foreign objects stuck in the door, or something stuck in the gap between the door and the body, causing the door to not close completely.
Damage to the door anti-collision beam or door lock mechanism: Damage to the anti-collision beam or door lock mechanism may cause the door to fail to open and close normally.
Aging deformation of the door seal: If the door seal is aging and worn seriously, it may affect the normal opening and closing of the door.
Vehicle chassis system failure: such as connecting rod, suspension system and other parts of the problem, may also affect the normal use of the door.
Software issues: There may be a software glitch in the vehicle's control system that prevents the doors from opening and closing properly.
The above problems need to be solved one by one. It is recommended to go to a professional repair shop for inspection and repair as soon as possible.
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAUXS auto parts welcome to buy.
