Front door can not open how to solve?
If your front door does not open, you can try the following workaround:
1. Check whether the cable of the door lock block is faulty. If the door can not be opened from the car, it is likely that the car door lock block cable failure can not be opened. In this case, the door lock block cable needs to be replaced in order to reopen the door.
2. Check the door lock status
If the door does not open, you can unlock it with the car key first, and then re-lock it twice. Next, locate the center lock button on the left front door trim of the main cab, press the unlock button, and try to open the door again. This may solve the problem.
3. Check whether the remote key works properly
If the remote key doesn't open the car door, the battery may be dead. You can try replacing the battery. If the battery is normal, but the other buttons are working normally, then there may be a problem with the gating part. In case the remote key is not available, you can temporarily use the mechanical key to open the door.
4. Check the child lock status
General vehicle rear door has a child lock, if the child lock is in the open state, directly close the door, the door will not be able to open. You need to take out the screwdriver and twist the child lock to the closed position so that you can open the door.
There's water in the front door. What's going on
The causes of water inside the door may include aging tape strips on the outside of the window glass, blocked drainage holes in the door, and water from vehicles parked in low-lying areas. Here are the details:
Aging of the outer strip of the window glass: As the age of the car increases, the outer strip of the window glass may age, causing moisture to enter the inside of the door along the gap in the glass.
Clogged door drain holes: Door designs often include drain holes to remove moisture entering the inside of the door. If these drainage holes are blocked by dust, sand, or other foreign objects, water cannot be discharged properly, resulting in water accumulation inside the door. Especially when the vehicle is in a rainy day or after a car wash, if the drainage hole is not smooth, it is more likely to lead to water problems.
Water in low-lying areas: If the vehicle is parked in a low-lying area, the water may be serious when it rains, causing rain water to enter the car through the door gap.
Solution: Regularly check the rubber strip on the outside of the window glass for signs of aging or damage, and replace it in time. At the same time, the drain hole of the door should be cleaned regularly to ensure that it is unimpeded. When parking, avoid parking your vehicle in low-lying or stagnant areas. If it is found that there is water in the door, it should be cleaned up in time, and the sealing performance of the door should be checked, and the sealing parts should be repaired or replaced if necessary.
Gap between front door and leaflet
The gap between the front door and the blade may be due to the wear of the door hinges or the wear caused by the prolonged use of the vehicle, as well as the gravitational action of the front engine and other components. In the case of excluding these factors, it is usually indicated that the front end of the fender or together with the front end of the longitudinal beam has shifted downwards. Similarly, the gap between the rear door and the rear fender appears large and small, usually caused by damage and deformation of the rear body downwards, and the gap between the rear door and the roof beam and the lower threshold will also appear uneven.
Adjustment method: First, you need to check whether the connector of the installation connection is crooked. If the leaf plate and trunk lid are found to be deformed, it is necessary to check whether the screw holes have been deformed by impact. Secondly, it is necessary to adjust the gap, first adjust the gap between the leaf plate and the door, then adjust the gap between the leaf plate and the cover, and finally adjust the gap between the headlight and the cover. If the above methods can not solve the problem, the sheet metal repair may not be done, you need to return to the factory repair, adjust the screw of the blade can be.
To a certain extent, this phenomenon is a manifestation of normal design and manufacturing tolerances, but excessive gaps may need to be solved by professional adjustment or maintenance. In the event of such problems, it is recommended to contact a professional car repair service for detailed inspection and necessary adjustments.
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAUXS auto parts welcome to buy.
