Replace the MG wiper coupling rod assembly disassembly steps are as follows :
Removing the wiper : First, you need to remove the wiper. This usually involves lifting and moving the wiper arm to a position at some distance from the windshield, then pressing the button on the wiper arm while pulling outwards on the upper end of the wiper blade to free it from the wiper arm. After this step, the old wiper can be removed and replaced with a new .
Lift the hood : Next, you need to lift the hood of your car. This usually involves removing the cover seal, lifting the cover, and uncoupling the spray hose to give access to the wiper coupling rod .
Removing the fixing screws and plastic parts : remove the fixing screws from the cover plate, unscrew the screws under the cover plate, and take out the plastic plate on the inside. The purpose of this step is to expose the parts of the wiper coupling rod for replacement .
Remove the motor and connecting rod : Remove the motor socket, unscrew the screws on both sides of the connecting rod, and then remove the motor from the old connecting rod and install it on the new connecting rod. Reinsert the assembly into the rubber hole of the coupling rod, tighten the screws, and plug the motor in .
recover parts : Finally, reinstall the rubber strip and cover plate in the reverse order of removal to restore the vehicle to its original condition .
The whole process requires patience and meticulous operation, ensuring that each step is carried out in the correct order to avoid damaging other parts of the vehicle. In addition, as it may vary from vehicle to vehicle, it is recommended to refer to the vehicle's owner's manual or watch the related video tutorial before proceeding with disassembly and replacement.
Mg wiper fault repair
Common causes of MG wiper failure include aging rubber blades, sprinkler system problems, wiring failures and setup problems.
rubber blade aging : Check the rubber blade of the wiper for cracks or hardening, if so, you need to replace the wiper.
Sprinkler system problem : Check that there is sufficient water in the glass water container, that the pipes are unimpeded, and that the nozzles are blocked. If the nozzle is blocked, use a fine needle to clear it. At the same time, check whether the pump is running normally. If the pump is faulty, it needs to be repaired or replaced in time.
line fault : Check whether the wire of the wiper is in poor contact or damaged. If the line fails, you need to repair the line or replace the damaged parts.
setup problem : Check whether the wiper is set correctly. For example, if the rotation speed is set too low, the driver may mistake the wiper for failure.
Through the above methods, you can effectively diagnose and solve the common fault problems of MG wiper.
Mg wiper instructions
The usage instructions of MG wiper mainly include automatic wiper, slow and fast wiper, point wiper, intelligent operation and other functions. Here's the detailed instructions:
Automatic wiper : Set the switch to automatic mode, and the wiper will automatically adjust the wiper frequency according to the speed of the vehicle. If there is a rain sensor next to the rearview mirror in the car, it will adjust the wiper speed according to the external rain conditions, so that the driving is more relaxed. Adjust the switch to finely control the sensitivity and ensure optimal wiper results.
Slow and fast wiper : when necessary, pull the lever upward to the corresponding position, you can switch to slow or fast mode, to meet the needs of different weather conditions.
spot wiper : Touch and hold the lever in the spot position. The wiper will scrape briefly to remove temporary rain or stains. If the lever switch is maintained in the point wiper position, the wiper will continue to wiper until it is released.
intelligent operation : when driving, just push the lever in the direction of the steering wheel of the car, the front windshield cleaner and the wiper will work simultaneously to ensure a clear vision.
In addition, the use of the MG HS wiper also includes front wiper and rear wiper operation. The adjusting lever of the front wiper is on the right of the steering wheel. The red box is for adjusting the front wiper and the blue box is for adjusting the rear wiper. The use of the front wiper includes spraying glass water and working with the wiper, lifting the lever up is to open the automatic wiper, and the knob can be adjusted to the corresponding gear according to the need. The use of the rear wiper is relatively simple, done by the knob in the blue frame of the illustration.
In order to better understand and operate MG wipers, you can refer to the relevant diagrams and video tutorials, these resources can intuitively show the specific steps and precautions for each function.
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAUXS auto parts welcome to buy.
