Car rear license plate light cover function
The main function of the light cover of the rear license plate is to illuminate the license plate and improve the safety of driving at night or in a dark environment . Specifically, the license plate light is located above the license plate at the rear of the vehicle, and its main function is to illuminate the license plate at night or in a dim environment, helping other vehicles and pedestrians to clearly identify the license plate number, thus improving driving safety . In addition, the installation of license plate lights is very simple, usually the use of screw shaped bulbs, installed above the license plate, not only play a lighting role, but also has a certain decorative effect .
According to relevant regulations, all vehicles must turn on the license plate lights behind the vehicle when driving at night to ensure that the license plate number can be clearly seen within the normal visual range at night (within about 20 meters) . License plate lights are usually controlled with the same switch as the vehicle's width or small lights to ensure that they can be turned on when required.
rear license plate light cover refers to a lamp installed above the rear license plate of an automobile and used to illuminate the license plate. Its main function is to provide sufficient lighting at night or in low light environments to help drivers and others clearly identify license plate numbers, while also helping to improve driving safety. In addition, the license plate light also has a certain decorative role .
Installation location and functions
The license plate light is usually installed above the rear license plate of the vehicle, and the bulb is in the shape of a screw and is directly fixed above the license plate. Its role is not limited to lighting, but also cooperating with the police for night tracking and surveillance when necessary .
According to relevant regulations, all vehicles must turn on their rear license plate lights when driving at night.
Replacement method
The steps to replace the rear license plate light are as follows:
Open the trunk, find the plastic cover holding the license plate light, and gently push on the sides to remove it.
Remove the wire connector, turn the license plate light counterclockwise and remove it.
Align the new license plate light with the mounting hole, turn clockwise to fix it, and connect the cable connector to ensure that the light is on.
Finally put the plastic cover back in place and secure it in place .
Care and maintenance advice
During the replacement process, ensure that the power is turned off to avoid the risk of electric shock and operate gently to avoid damaging other parts of the vehicle. If you are not familiar with the operation or have any questions, it is recommended to seek the help of professional technicians .
Failure of the rear license plate light cover usually refers to a problem with the lighting equipment of the rear license plate light of the vehicle, resulting in the failure of the license plate light to work properly. This failure may affect the safe operation of the vehicle, especially at night or in low light.
Fault cause
bulb damage : Bulb burnout of license plate lights is one of the most common causes. If the bulb does not light, it will trigger the fault indicator light to light .
circuit problem : poor circuit contact, short circuit or open circuit may also cause the license plate light to not work normally. These problems can cause voltage instability, which can prevent license plate lights from lighting properly .
blown fuse : If the vehicle's fuse is blown, it will cause the license plate light to fail to supply power, which will trigger the fault light .
sensor failure : The sensor responsible for monitoring the status of the lamp may be faulty, causing the system to misjudge the status of the license plate light .
Control module failure : In some advanced models, the control of the license plate light may be implemented by the body control module (BCM) or the Light control module (LCM). If these modules fail, it may also cause the license plate lights to not work properly .
solution
check the bulb : First check whether the bulb of the license lamp is burned out. If so, replace the bulb with a new one .
Check the circuit connection : ensure that the circuit connection is firm and not loose or poor contact. Check whether the circuit is short or open, and repair .
Check the fuse : check whether the relevant fuse of the license plate light in the car fuse box is burned out, if yes, replace the corresponding fuse .
professional inspection : If the above methods are ineffective, it is recommended to send the vehicle to a professional maintenance site for inspection and repair .
Reset system : Try disconnecting the negative battery line for a brief system reboot to eliminate possible temporary software issues .
Use the diagnostic tool : Use a professional automotive diagnostic tool to read the fault code and further locate the problem .
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&750 auto parts welcome to buy.