How to install the MAXUS G10 engine thrust blade?
1, the first step: first install the crankshaft in the axle box, add lubricating oil. Step 2: Install the crankshaft. Step 3: Lubricate the thrust plate. Step 4: Lubricate the place where the thrust plate is installed. Step 5: Place the thrust plate in the center of the crankshaft.
2, the crankshaft thrust plate is two pieces, only installed on the front and rear thrust surface of the main bearing seat of the cylinder body; Add engine oil to the slotted surface of the thrust plate before installation; Put the oil-free surface towards the cylinder block and the oil-groove surface towards the crankshaft into the thrust plate groove of the fourth main bearing seat; Note that the oil groove face of the thrust plate faces the crankshaft side.
3, Install the Santana engine thrust plate, first install the crankshaft box inside the grease, install the crankshaft, the specific steps are as follows: First install the crankshaft box inside the grease. Install the crankshaft. Grease the thrust plate. Grease the area where the thrust plate is installed.
4. The steps to install the B12 engine thrust plate are as follows: Clean the body contact surface and thrust plate mounting interface. This is to ensure that the thrust plate is fully integrated with the fuselage contact surface to ensure normal operation. Insert the thrusters into the fuselage, making sure they are fully embedded and have no taper, cracks, or other damage.
5. Prepare tools and materials. The tools required for installing a crankshaft thrust plate include a wrench, screwdriver, rubber mallet, and lubricating oil. Materials include crankshaft thrust plate, thrust plate mounting screws, thrust plate mounting gaskets, etc. Cleaning work. Before installing the crankshaft thrust plate, clean the crankshaft and related parts.
6. Installation method: The thrust plate adjusts the axial clearance of the crankshaft, and forms an O-type gasket between the tile seat and the shaft table. If you can put one down, you can put two down. Note that the ground side faces the crankshaft. Then see whether the thickness of the gasket and the gap are matched.
1. Little impact. I don't know if you're referring to replacing the middle part of the engine, that is, the cylinder block. If this is the case, the impact must be there, the need to re-run, may reduce the engine power.
2, change the cylinder, but also change the piston assembly, no impact on the car, but must be re-run. Note the same as the new car run-in. Replace the oil after running-in can be used normally. The engine is composed of valve chamber cover, cylinder head, cylinder block (middle cylinder) and oil pan from top to bottom. The middle cylinder is the larger cast iron thing on the engine.
3, the impact of engine cylinder replacement on the engine cylinder replacement on the impact of engine cylinder replacement on the engine cylinder replacement attention is not to install the wrong, the number of commonly used car engine cylinders are 12.
4, the disadvantage of replacing the engine block is: the performance of the engine may be affected: the replacement of the cylinder block may affect the structure and performance of the engine, because the new cylinder block may be different from the old cylinder block, and it may be necessary to readjust the valve, ignition time and other technical parameters.
engine crankshaft thrust plate wear abnormal sound symptoms
Engine crankshaft thrust plate wear will cause the following abnormal sound symptoms :
abnormal sound : When the crankshaft thrust plate is worn, there may be movement between the crankshafts, causing the engine to emit abnormal sound.
power drop : crankshaft thrust plate wear will affect the balance of the engine, resulting in reduced power output.
jitter : The balance of the engine is destroyed, causing the vehicle to jitter during driving.
flameout : serious crankshaft failure may lead to sudden engine flameout, affecting driving safety.
The cause of engine crankshaft thrust plate wear
Causes of crankshaft thrust wear may include :
wear : Long-term use and friction lead to wear of the thrust plate, which affects the stability of the crankshaft and the performance of the engine.
poor lubrication : failure of the lubrication system or poor lubricating oil quality accelerates the wear of the thrust plate.
Improper installation : Improper operation or design defects during installation may also cause wear of the thrust plate.
The method to solve the abnormal sound of engine crankshaft thrust plate wear
Solutions to crankshaft thrust wear include :
Replace thrust plate : Replace worn thrust plate in time to restore engine balance and performance.
Check the lubrication system : check the quality and supply of the lubrication system to ensure good lubrication and reduce wear.
regular maintenance : Check and maintain the engine regularly to find and solve problems in time to avoid more serious damage.
If you want to know more, keep reading the other articles on this site!
Please call us if you need such products.
Zhuo Meng Shanghai Auto Co., Ltd. is committed to selling MG&MAUXS auto parts welcome to buy.
